Please do take care to read the information thoroughly as it is there to help you understand fault codes and to keep you safe. There are also some help, tips and hints with a lot of the fault codes published here that you usually will not find anywhere else and, as we learn, we add more information so if you can't find what you need please ask in the forums.
Before using this section please understand that fault or error codes are used as a diagnostic aid, they are not a replacement for diagnostic skill on the part of the person repairing the product and are not in any way usually going to point to the precise component that is faulty. All they do is give you an idea of where to start looking for the fault.
Beko WMA Washing Machines With Display Error codes
These error code explanations can help you diagnose a problem with your Beko WMA Washing Machines With Display.
North London Appliances Repair forums
We add more information as we learn so if you can't find what you need please ask in the Repair forums.
E1
NTC error detected
- Issue:
- NTC error detected
- Advice:
- Check wiring
- Check thermistor which will normally read approximately 4700 Ohms at 25˚C
E2
Not heating error
- Issue:
- Not heating error
- Advice:
- Check heater as it is detected as being open circuit
- Check wiring
E3
Constant heat
- Issue:
- Advice:
- Check wiring
- Check control board relay for heater
E4
Filling error detected
- Issue:
- You can see the machine constantly filling and discharging water, no wash action or the door is jammed causing this error to occur.
- Advice:
- Check water valve
- Check valve triac on PCB
- Check PCB
- Check wiring
E5
Failure to drain
- Issue:
- Often this is reported as being a failure to drain the water from the washing machine, the program taking too long or not spinning.
- Advice:
- Check for blockages or obstructions in the pump filter
- Check pump
- Check pump triac on PCB
- Check control board
E6
Motor fault detected
- Issue:
- Often the complaint when this error occurs is that teh washing machine will move a couple of times then the program will end, the machine will jump to spin during a wash or the program is unfinished.
- Advice:
- Check motor
- Check wiring
- Check motor triac on control PCB
- Check PCB
E7
Level sensor error
- Issue:
- The complaint will be that the washing machine empties every time it is started of that the program simply does not start.
- Advice:
- Check wiring to level sensor
- Check level sensor
E8
Failure to fill with water
- Issue:
- The washing machine will fail to fill leading to complaints that the program takes too much time, the program does not end, the machine will not fill with water or that the washing machine just drains and nothing else.
- Advice:
- Check water valve
- Check anti flood system if fitted
- Check wiring
- Check water valve triac
- Check pump triac
- Check control PCB
E9
Door lock triac failure
- Issue:
- Advice:
- Check door lock
- Check wiring
- Check door lock triac on the main control PCB
- Check control PCB for operation
E10
Door error
- Issue:
- The door is detected as being jammed
- Advice:
- Check door
- Check door lock
- Check door lock wiring
- Check door lock triac on the control module
- Check control module
E11
Motor error detected
- Issue:
- Motor error detected
- Advice:
- Check motor
- Check wiring
- Check motor triac on control PCB
- Check PCB
E17
Excessive foam detected
- Issue:
- Generally this will be as a result of overfoaming from an incorrect detergent being used, a poor quality detergent being used or from overdosing. This is common across many brands especially in soft water areas.
- Advice:
- This can take some time to clear and it is advised that you run several rinse only programs to clear any residue detergent still in the washing machine.
- Reduce detergent dose and restart program
E18
Unbalanced load detected
- Issue:
- This error can be displayed where the machine has failed to spin or the time can seem to be extended.
- Advice:
- Sort load and retry spin. If this fault indicator occurs again, please arrange an engineer visit. We offer fixed price Beko Washing Machine Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.
Arrange a visit from a Washing Machine engineer
If you do need an engineer to visit your home, help is at hand. We’ll arrange for an engineer near you to call in and fix your appliance, at a time that’s suitable for you.
Book online or give us a call on 0208 226 3633
London Only - Coverage Area | ( Monday - Friday: 8:00 - 20:00 / Saturday: 09:00 - 18:00 )
Warning! To avoid personal injury or death, always unplug the appliance or disconnect the power before attempting any repairs. Always turn off the gas at the source before repairing any gas appliance. Always wear safety glasses when using tools. Keep loose clothing and hair away from any moving parts. Safety is of major importance when performing any service or repair on any electrical appliance. Please, read our disclaimer before proceeding.
