E00

No alarm

Issue:

No alarm

Advice:

E3A

Faulty sensing by heating resistance relay

Issue:

Faulty sensing by heating resistance relay. Main board defective. Cycle stops with door locked OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E10, C1

My Washing Machine shows the error code "E10" or C1

Issue:

The difficulties you are facing may be due to different causes. Please use our troubleshooter for an appropriate investigation.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E10/E11/E12

Inlet Valve

Issue:

If your washing machine is displaying either an E10, E11 or E12 error code, it is likely that there is a problem with the water filling the drum.

Advice:

If the water supply is turned on and the hose pipe is not kinked the problem may be due to a faulty inlet valve. Check the inlet valve with a multimeter to confirm continuity - typically 2000 to 4000 Ohms.

E11

Filling error

Issue:

Poor fill before wash cycle. Tap off or water pressure too low. Drain hose improperly positioned. Fill valve is defective. Leaks on pressure switch. Pressure switch failed. Wiring fault. Main board defective. Cycle is paused with door locked Start

Advice:

This is usually your basic filling error so the usual should be checked, that the water supply is switched on and then onto the water fill valves. If this fault indicator occurs again, , please arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E12

Difficulty in fill during drying

Issue:

Difficulty in fill during drying (maximum time 3 min. fill in drying during the wash load phase). Tap off or water pressure too low Valve failed. Pressure switch water circuit. Pressure switches. Wiring. Main PCB. Cycle is paused

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E13

Pressure switch faulty

Issue:

Water leaks Drain hose improperly positioned. Water pressure too low. Fill valve is defective. Water circuit on pressure switch is leaking or blocked. Pressure switch faulty. Cycle is paused with door locked

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E20

My washing machine shows error "E20"

Issue:

The difficulties you are facing may be due to different causes. Please use our troubleshooter for an appropriate investigation.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E21/E22/E23/E24

Blocked Filter

Issue:

If your washing machine is beaming at you with either an E21, E22, E23 or E24 error code, then most likely there is a problem with draining the water

Advice:

• Drain the water from the machine by lowering the drain hose below the water level to a bowl or your machine may have a drain hose near the filter
• Place a towel under the filter and pull the filter out to remove any debris that may have gathered.
• Check the pump impeller inside the housing turns freely and is not obstructed.

E21

Poor draining

Issue:

Poor draining. Drain hose kinked/clogged/improperly positioned. Drain filter clogged/dirty. Drain pump faulty. Pressure switch faulty. Wiring faulty. Main board faulty. Current leak between heating element and ground. Cycle is paused Start

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E22

Difficulty in fill during drying or drying condenser blocked

Issue:

Difficulty in fill during drying or drying condenser blocked (pressure switch closed on “FULL”). Drain hose kinked. Filter blocked. Drying condenser blocked. Drain pump faulty. Pressure switches faulty. Wiring. Main circuit board faulty. Current leakage between heater and ground. Cycle is paused Start

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E23

Defective triac for drain pump

Issue:

Defective triac for drain pump. Drain pump faulty. Wiring faulty. Main board faulty. Emergency drain procedure - Cycle stops with door unlocked OFF/reset

Advice:

This refers to the triac that controls the pump function on the main controller. If the fault persists, please arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London, you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit.

E24

Malfunction in sensing circuit on triac for drain pump

Issue:

Malfunction in sensing circuit on triac for drain pump. Main board faulty. Emergency drain procedure - Cycle stops with door unlocked OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E30

Door Lock

Issue:

If the digital display on your washing machine is showing either E30 error code, the most likely cause for this could be a faulty door lock.

Advice:

Check the door - you need to confirm that the lock does engage correctly. If there is power to the washing machine and the lock does not engage you will need to replace the lock.

E31

Malfunction in pressure switch circuit

Issue:

Malfunction in pressure switch circuit (frequency of signal from pressure switch out of limits). Pressure switch faulty. Wiring. Main PCB faulty. Cycle stops with door locked OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E32

Electronic pressure switch improperly calibrated

Issue:

Electronic pressure switch improperly calibrated (level on electronic pressure switch differs from 0-66 mm after initial calibration drain and when anti-boiling pressure switch is on “empty”). Tap is off or water pressure is too low. Fill valve faulty. Water circuit on pressure switches. Pressure switches. Wiring. PCB faulty. Cycle is paused Start

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E33

Inconsistency between level on electronic pressure switch and level on anti-boiling pressure switch 1-2

Issue:

Inconsistency between level on electronic pressure switch and level on anti-boiling pressure switch 1-2 (fault persists for at least 60 sec.). Pressure switch defective. Current leak between heating element and ground. Heating element. Wiring faulty. Main board faulty. Water circuit. Emergency drain procedure - Cycle stops with door unlocked OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E34

Inconsistency between level on electronic pressure switch and level on anti-boiling pressure switch 2

Issue:

Inconsistency between level on electronic pressure switch and level on anti-boiling pressure switch 2 (fault persists for at least 60 sec.). Pressure switch faulty. Electrical current leak between heating element and ground. Heating element faulty. Wiring faulty. Main board faulty. Water circuit. Emergency drain procedure - Cycle stops with door unlocked OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E35

Overflow error

Issue:

Overflow error. Fill valve is faulty. Leaks from water circuit on pressure switch. Pressure switch defective. Wiring defective. Main board defective. Cycle stops - Emergency drain procedure - Drain pump continues to operate (5 min. on, then 5 min. off, etc.). OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E36

Sensing circuit on anti-boiling pressure switch 1 defective

Issue:

Sensing circuit on anti-boiling pressure switch 1 defective. Main board faulty. Cycle stops with door locked OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E37

Sensing circuit on anti-boiling pressure switch 2 defective

Issue:

Sensing circuit on anti-boiling pressure switch 2 defective. Main board faulty. Cycle stops with door locked OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E38

Internal pressure takeoff is blocked

Issue:

Internal pressure takeoff is blocked (water level does not change for at least 30 sec of drum rotation). Water circuit on pressure switches. Pressure switches. Motor belt broken. Heating phase is skipped

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E39

Defective HV sensing on anti-overflow system

Issue:

Defective HV sensing on anti-overflow system. Main board faulty. Cycle stops with door locked OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E40

My Washing Machine shows the error-code "E40"

Issue:

The difficulties you are facing may be due to different causes. Please use our troubleshooter for an appropriate investigation.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E41

Door lock faulty

Issue:

Door unlocked. Door lock faulty. Wiring faulty. Main board faulty. Cycle is paused Start

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E42

Problem closing the door

Issue:

Problem closing the door. Door lock faulty. Wiring faulty. Main board faulty. Cycle is paused Start

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E43

Defective triac supplying power to door delay system

Issue:

Defective triac supplying power to door delay system. Door lock unit faulty. Wiring faulty. Main board faulty. Emergency drain procedure - Cycle stops OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E44

Defective sensing by door delay system

Issue:

Defective sensing by door delay system. Main board faulty. Emergency drain procedure - Cycle stops OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E45

Defective sensing by triac on door delay system

Issue:

Defective sensing by triac on door delay system. Main board faulty. Emergency drain procedure - Cycle stops OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E50

My Washing Machine Shows the error code "E50"

Issue:

The difficulties you are facing may be due to different causes. Please use our troubleshooter for an appropriate investigation.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E51

Motor power supply triac short-circuited

Issue:

Motor power supply triac short-circuited. PCB faulty. Current leakage from motor or from wiring loom. Cycle blocked, door locked (after 5 attempts) OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E52

No signal from motor tachometric generator

Issue:

No signal from motor tachometric generator. Motor faulty. Wiring faulty. PCB faulty. Cycle blocked, door locked (after 5 attempts) OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E53

Motor triac sensing circuit faulty

Issue:

Motor triac sensing circuit faulty. PCB faulty. Cycle blocked, door locked OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E54

Motor relay contacts sticking

Issue:

Motor relay contacts sticking. PCB faulty. Current leakage from motor or from wiring. Cycle blocked, door locked (after 5 attempts) OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E56

Carbon Brushes

Issue:

If the digital display on your washer showing any of the following error codes E56, the likely cause for this would be a defective motor.

Advice:

Once you have access remove the motor. Check for wear on the carbon brushes and replace if required.

E57

Carbon Brushes

Issue:

If the digital display on your washer showing any of the following error codes E57, the likely cause for this would be a defective motor.

Advice:

Once you have access remove the motor. Check for wear on the carbon brushes and replace if required.

E58

Carbon Brushes

Issue:

If the digital display on your washer showing any of the following error codes E58, the likely cause for this would be a defective motor.

Advice:

Once you have access remove the motor. Check for wear on the carbon brushes and replace if required.

E59

Carbon Brushes

Issue:

If the digital display on your washer showing any of the following error codes E59, the likely cause for this would be a defective motor.

Advice:

Once you have access remove the motor. Check for wear on the carbon brushes and replace if required.

E60

My Washing Machine shows the error code "E60"

Issue:

The Error code E60 or any other code beginning with E6 generally refers to the fact that there is a heating problem with your machine. This type of error can only be resolved by booking a service engineer.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E61

Insufficient heating during washing

Issue:

Insufficient heating during washing. NTC sensor faulty. Heating element faulty. Wiring faulty. PCB faulty. The heating phase is skipped

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E62

Overheating during washing

Issue:

Overheating during washing. NTC sensor faulty. Heating element faulty. Wiring faulty. PCB faulty. Safety drain cycle - Cycle stopped with door open OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E66

Heating element power relay faulty

Issue:

Heating element power relay faulty. PCB faulty. Current leakage from heating element to ground. Safety drain cycle - Cycle stopped with door open OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E71

NTC sensor for wash cycle defective

Issue:

NTC sensor for wash cycle defective. Faulty NTC sensor. Wiring faulty. Main board faulty. Heating is skipped revert to Start

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E72

Fault in NTC sensor on drying condenser

Issue:

Fault in NTC sensor on drying condenser (voltage out of range = short-circuit, open circuit). Drying NTC sensor (condenser) faulty. Wiring faulty. Main circuit board faulty. Heating is skipped revert to Start

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E73

Fault in NTC sensor on drying duct

Issue:

Fault in NTC sensor on drying duct (voltage out of range = short-circuit, open circuit). Drying NTC sensor (duct) faulty. Wiring faulty. Main circuit board faulty. Heating is skipped revert to Start

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E74

NTC sensor for wash cycle improperly positioned

Issue:

NTC sensor for wash cycle improperly positioned. NTC sensor incorrectly positioned. Faulty NTC sensor. Wiring defective. Main board faulty. Heating is skipped revert to Start

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E82

Error in selector reset position

Issue:

Error in selector reset position. PCB faulty (Wrong configuration data). Selector, wiring faulty. OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E83

Error in reading selector

Issue:

Error in reading selector. PCB faulty (Wrong configuration data). Selector, wiring. Cycle cancelled

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E84

"Sensing" circuit on circulation pump triac faulty

Issue:

"Sensing" circuit on circulation pump triac faulty (input signal to processor always 0V or 5V). PCB Drain. Cycle blocked (door open). OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E85

Circulation pump faulty

Issue:

Circulation pump faulty (incongruency between status of "sensing" circuit on circulation pump and status of TRIAC). Circulation pump. Wiring. Main PCB. Drain, cycle blocked (door open). OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E90, E91, E92, E93, E94

My washing machine shows error message E90, E91, E92, E93 or E94

Issue:

The Error codes E91, E92, E93 and E94 or any other code beginning with E9 are related to electronic configuration/communication problems on the appliances. Please make a reset at the washing machine by unplugging it, waiting 30 seconds and plugging it again.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E91

Communication incongruence between main PCB- display board

Issue:

Communication incongruence between main PCB- display board (versions not compatible). Wiring faulty. Faulty control/display board. Main PCB faulty. Cycle interrupted

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E92

Communication incongruence between main PCB- display board

Issue:

Communication incongruence between main PCB- display board (versions not compatible). Wrong control/display board. Wrong PCB (do not correspond to the model). Cycle interrupted

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E93

Incorrect configuration of appliance

Issue:

Incorrect configuration of appliance. Incorrect configuration data. PCB faulty. Cycle interrupted OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E94

Incorrect configuration of washing cycle

Issue:

Incorrect configuration of washing cycle. Incorrect configuration data. PCB faulty. Cycle interrupted OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E95

Communication error between microprocessor and EEPROM

Issue:

Communication error between microprocessor and EEPROM. PCB faulty. Cycle interrupted OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

E97

Incongruence between programme selector and cycle configuration

Issue:

Incongruence between programme selector and cycle configuration. Faulty PCB (Wrong configuration data). Cycle interrupted OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

EB1

Frequency of appliance incorrect

Issue:

Frequency of appliance incorrect. Power supply problems (incorrect / disturbance). PCB faulty. Cycle interrupted

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

EB2

Voltage too high Power supply problems

Issue:

Voltage too high Power supply problems (incorrect / disturbance). PCB faulty. Cycle interrupted

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

EB3

Voltage too low

Issue:

Voltage too low. Power supply problems (incorrect / disturbance). PCB faulty. Cycle interrupted

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

EC1

Solenoid valve inoperative but flow meter operating

Issue:

Solenoid valve inoperative but flow meter operating. Main board faulty. Fill valve faulty. Cycle stops with door locked (after 5 attempts). OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

EC2

Signal from turbidity sensor out of limits

Issue:

Signal from turbidity sensor out of limits. Turbidity sensor faulty. Main board faulty. Wiring faulty. Start/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

EC3

Signal from weight sensor out of limits

Issue:

Signal from weight sensor out of limits. Weight sensor faulty. Main board faulty. Wiring faulty. Start/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

EF0

My Washing Machine shows error "EF0"

Issue:

The difficulties you are facing may be due to different causes. Please use our troubleshooter for an appropriate investigation.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

EF1

Drain filter blocked

Issue:

Drain filter blocked (too long drain phase). Drain tube blocked/kinked/too high. Drain filter dirty/blocked. Warning displayed at the end of cycle (specific LED)

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

EF2

Overdosing of detergent

Issue:

Overdosing of detergent (too much foam during drain phases). Excessive detergent dosing. Drain tube kinked/blocked. Drain filter dirty/blocked

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

EF3

Control water intervention

Issue:

Control water intervention. Water leakage on the base. Faulty water control device. Water drain and cycle blocked OFF/reset

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

EF4

Low pressure of water fill

Issue:

Low pressure of water fill, no signal of flow meter and solenoid open. Tap closed, low water fill pressure - Reset

Advice:

Tap closed, low water fill pressure - Reset
We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

EH0

My washing Machine is displaying the error message "EH0"

Issue:

The difficulties you are facing may be due to different causes. Please use our troubleshooter for an appropriate investigation.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

C1

My Washing Machine shows the error code "C1"

Issue:

The difficulties you are facing may be due to different causes.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

C2

My washing machine shows error "C2"

Issue:

The difficulties you are facing may be due to different causes. Please use our troubleshooter for an appropriate investigation.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

My washing machine shows an error

Issue:

The difficulties you are facing may be due to different causes. Please use our troubleshooter for an appropriate investigation.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.

My washing machine showed an error and did not pump off the water

Issue:

The difficulties you are facing may be due to different causes. Please use our troubleshooter for an appropriate investigation.

Advice:

We add more information as we learn so if you can't find what you need please ask in the Repair forums. Alternatively you can book a repair online or call us on 0208 226 3633 to arrange an engineer visit. We offer fixed price AEG Washing Machine Repairs in London.